Draw-out vs Fixed LV Switchgear: Serviceability, Heat and Busbar Layout

Two quotations for the same 400 V, 630 kVA board often differ by 25–40 percent, and the gap is almost always draw-out versus fixed. Buyers assume they are paying for the ability to pull a module out. What they are paying for is who absorbs the outage: draw-out compresses a circuit outage into a unit swap, while fixed hands that time to the electrician and the spares shelf. This article works through the three things that decide it — serviceability, heat, busbar layout — and the sheet metal details that make or break a draw-out cubicle.

1. The decision on one page

  • Staffed 24/7, load added in phases, one circuit outage costs output — draw-out.
  • Circuits fixed at day one, outages fit a maintenance window — fixed, and the saving buys two spare breakers.
  • Most projects hybridise: fixed incomer and bus-tie, draw-out feeders.
  • Do not copy "draw-out" out of a tender template. A cheap draw-out board fails more often than a well-built fixed one.

The three dimensions are separable: serviceability is MTTR, heat is derating, busbar layout is space and short-circuit. Work them in that order and the answer usually falls out.

2. Two mechanical formats, one electrical duty

  • Draw-out: breaker, contactor and CTs in a removable drawer, connected to the vertical riser through isolating contacts, control on a plug. Three positions: connected, test, disconnected.
  • Plug-in: device fixed, line and load connections plug-in for fast swap. Two positions only, and the door still opens.
  • Fixed, bolted: cable or busbar lands on the breaker terminals. Replacement means stripping, tagging, re-crimping, re-insulating, re-testing.
  • Electrically all three can be identical; the difference is replaceability against contact count. Every draw-out circuit adds three phases plus N and PE of contact interface — convenience and a new failure mode together.

3. Module heights and the space arithmetic

Draw-out systems are laid out in modules of E = 25 mm: 8E (200 mm) is the usual minimum, then 16E (400 mm) and 24E (600 mm). A 2,200 mm cubicle gives roughly 1,800 mm (72E) of height, and after the top busbar zone, bottom cable zone and instrument panel you have 56–64E to allocate.

Unit heightTypical dutyUnits per sectionDepth needed
8E / 200 mmMotor circuits to 15 kW, metering8–9600 mm, 800 better
16E / 400 mm250–630 A feeders with CTs4800 mm
24E / 600 mm630–1250 A feeders2–31000 mm

Draw-out saves cubicles, not depth. The same circuit count often needs one or two fewer sections, but each grows from 600 mm to 800–1000 mm deep, so floor area does not fall in proportion. Cost the room by footprint, not by cubicle count. Then reserve 15–20 percent spares and fit the contact blocks, shutters and control plugs at build time — a bare spare space is a future rebuild, not a spare.

4. Serviceability: what draw-out actually buys

The MTTR difference is not a factor of two; it is an order of magnitude.

  • Draw-out swap: isolate, rack out, rack in the spare, close — 10–20 minutes, no cable touched.
  • Fixed swap, same rating: isolate, prove dead, disconnect and tag four cables, unbolt, rebolt, torque, insulation test, re-energise — 1.5–4 hours.
  • What differs more is who can do it. Any shift electrician swaps a drawer; re-terminating needs a qualified person and a torque record (20–25 N·m for M8, 35–45 N·m for M10 copper lugs).
  • Spares diverge too. Draw-out stocks units, one 16E drawer covering a dozen circuits; fixed stocks by breaker model, value scaling with model count.

Draw-out also moves the skill requirement from wiring to mechanical operation and concentrates risk in the contacts. When such a board misbehaves it is the isolating contacts, the control plug or rail alignment — rarely the breaker.

5. Heat: two paths out of the cubicle

A drawer packs breaker, contactor and CTs into 200 mm, so loss density is high and heat leaves only by the front and top. A fixed cubicle has fewer devices and open space, so natural convection up the frame works. That single difference drives the whole thermal strategy.

  • Draw-out: roof fans, two to four at 25–40 W each, or a roof cooling unit. Intake and exhaust need dust filtration and rain protection.
  • Fixed: bottom intake and a louvred roof for most ratings; only dense busbar sections need local ventilation.
  • Above 45 °C ambient — the Gulf, much of Southeast Asia — draw-out must be derated. Against GB/T 7251.1 limits (bare copper 105 K, bolted terminals 70 K, draw-out contacts 70 K), a 50 °C room costs 10–15 percent of rated current.
  • Spare compartments need a full shutter, not just a blank panel. Otherwise heat crosses from the neighbour and the next unit installed there trips.

Measured: at 630 A, air around the breaker runs 8–12 K hotter in a drawer than in a fixed cubicle, roof exhaust 5–8 K. Either add fans or go up one breaker frame size — similar cost, and the larger frame costs less to maintain.

6. Busbar layout: rear, side, sandwich

Where the vertical riser sits decides depth, usable drawer width and how short-circuit supports are arranged. Lock it before fabrication; changing it later means new cubicles.

Riser positionDepthStrengthLimit
Rear compartment800–1000 mmBest cooling, easiest supportsCosts depth, needs rear access
Side column600–800 mmCompact, wider drawersSupport spacing hard at 65 kA
Sandwich600 mmSmallest footprintTightest fabrication tolerance

Choose by fault level first. Up to Icw 50 kA/1s all three work; at 65 kA and above, rear risers take insulation supports most easily at 600 mm maximum spacing, with one at every partition crossing. Side risers are squeezed by drawer depth; sandwich demands the tightest fabrication. Watch the neutral: draw-out boards run N at full phase section and PE at half, but downstream of UPS or with high harmonic content N should be 1.5–2 times phase.

7. Isolating contacts and position interlocks

  • Silver thickness: 3–5 µm normal. Below 3 µm, sulphur and salt air oxidise the plating and resistance climbs monthly. Coastal Gulf and humid Southeast Asian projects should specify 5 µm in writing.
  • Contact pressure: 20–30 N per finger from the spring. Low pressure degrades resistance and temperature together and nothing shows from outside — only a temperature-rise test or thermal imaging finds it.
  • Operating life: 500–1000 mechanical operations, enough for weekly use over twenty years. Commissioning racking is what consumes it; do not rack units without reason.
  • CT shorting: racking out must short the CT secondary first, or the open circuit produces dangerous voltage. Proper units use a linked shorting bar, not operator sequence.
  • Three interlocks: no racking with the breaker closed; no closing unless the drawer is connected or in test; shutters close over live blocks at disconnected.
  • Earthing: sliding contact or braided shunt, unbroken through the travel, measured at 0.1 Ω or less — the check most often skipped at FAT.

8. Ten-year cost and tender wording

For eight sections with 24 feeders over ten years, draw-out costs about 25 percent more up front. Add one unplanned outage — eight hours at CNY 8,000 per hour is CNY 64,000 — plus the spares difference, and most plants break even in four to six years. With dual incomers, a bus-tie and a generator already in place, that argument collapses.

  • Draw-out or fixed, circuit by circuit, never "LV boards, one lot".
  • Module heights, a per-section circuit allocation table and the spare count.
  • Icw (kA/1s), Ipk, and the type-test report number with issuing laboratory.
  • Silver thickness, contact pressure and operating life as numbers, not adjectives.
  • Form of separation down to the a/b suffix, with the three barriers named.
  • Maximum ambient with the derating that follows: 40–45 °C Southeast Asia, 45–50 °C Gulf, stated separately.
  • Enclosure IP and ventilation method; routine test list including dielectric, insulation resistance, circuit continuity and 50 mechanical operations.

9. Sheet metal details that decide reliability

  • Frame profiles 2.5 mm cold-rolled or galvanised; drawer shelves 1.5–2.0 mm, rated 100 kg per tier and load-tested.
  • Rails 2.0 mm galvanised, left-right synchronisation within 1 mm. Rails out of parallel skew contacts on racking and unbalance phase pressure — a leading cause of early heating.
  • Contact apertures held to ±1 mm and laser cut in one pass. Drilling oversize and filing back lands at 2 mm and never recovers.
  • Frame verticality within 1.5 mm/m, diagonals within 3 mm. Weld distortion a fixed cubicle shrugs off becomes a drawer that will not go in.
  • Mask earth studs and drawer sliding surfaces before coating, or the earth test fails and the fix is a full recoat.

Yuan Electric (Suzhou) has built sheet metal enclosures and non-standard structures for 15 years, with a 52-person team, a 5,000+ m² plant and 20-plus laser cutting, CNC bending and welding machines. Standard orders ship in 7–15 days and we work from drawings or samples. Cubicle frames, drawer shelves, busbar supports, contact apertures and coating masking are produced to drawing in one pass, with dimensional and earthing checks before dispatch.

Frequently asked questions

How much more does draw-out cost for the same circuits?

25–40 percent at typical specifications, sitting in isolating contacts, drawer hardware and cubicle accuracy. The premium scales with circuit count and falls as current rises, so incomer sections show almost no difference.

Can a draw-out board reach IP54?

Yes indoors, but heat rejection drops sharply and you need a cooling unit or heat exchanger. In dusty plants, specify IP54 plus internal pressurisation rather than simply raising the IP number.

Can a fixed board be converted later?

No. Riser position, cubicle depth, shelf modules and contact apertures all differ, so conversion costs more than a new board. Decide at specification stage.

What Icw should we specify?

Take the prospective fault level at the installation point and add one step. A 630 kVA transformer secondary is usually 25–31.5 kA, so 50 kA/1s for the main board is sensible; 65 kA pushes depth and busbar size up for nothing.

How do we protect contact life on a coastal site?

Three measures together: 5 µm silver, IP54 with anti-condensation heaters, and one annual thermal scan plus contact pressure sampling. Do all three and the contacts last beyond ten years.

What lead time should we plan for?

15–25 days for standard LV assemblies, 25–35 with Form 4 separation and type-test documentation. Draw-out adds 5–8 days over a fixed board of the same rating, so book contact blocks and drawer frames early.

Related: Our Capabilities · All technical articles · 中文版
→ View all products · Contact us